PDA

View Full Version : Diamond plate floor / vibrating floor?



NightmareAftershockLLC
07-06-2013, 12:19 AM
Visited Ghostly Manor, and I loved the elevated diamondplate floor that vibrated with some sort of motor underneath of it... Vibrated your feet

Anyone have ANY idea of a kit or a DIY instructional for how this is done?

I'm assuming someone makes a kit?

Thanks! :)

Nic Miele
07-06-2013, 01:21 AM
http://www.frightprops.com/frightprops-transducer-shaker-0527.html

Fright Props sells Great Shakers!!!


Nic Miele
The Massacre Haunted House

Jim Warfield
07-06-2013, 08:50 AM
.. would be the Beach Boy's song "Good Vibrations?" OR the older song "All Shook Up?"

NightmareAftershockLLC
07-06-2013, 10:02 AM
We're definitely looking for a much cheaper setup. By the time we hook up amps and everything we're out 700 bucks. I KNOW they didn't use this, as it rattled when stepped on, even when turned off.

NightmareAftershockLLC
07-06-2013, 10:10 AM
Almost felt like a chain semi welded with some sort of motor to turn metallic something hitting it? Hmmmm

Allen H
07-06-2013, 11:12 AM
I have seen them done with concrete vibrators, reciporicating saws, and power chisels/jack hammers. A plate is welded to the floor and the power tool has a blunt bit that strikes against it. Very effective. Zip tie the trigger in and use the power plug as the on/off. eventually the tool will wear through the floor but how often depends on throughput- figure once every other season. Note: set the tool up paralell to the walking surface striking a plate like I said earlier, you dont want a power tool shooting through into someones foot. with this set up a wear through just means it makes noise but no vibrations.
I hope that helps,
Allen H

Allen H
07-06-2013, 11:21 AM
here is an older thread on the same thing- read Gadget's comments
http://www.hauntworld.com/haunted_house_forums/showthread.php?910-vibrating-floor

NightmareAftershockLLC
07-06-2013, 12:21 PM
Allen, perfect. Thank you sir! It certainly was an effective startle!!!

This got the proverbial brainstorming rolling. Much appreciation!

brucejuice39
07-06-2013, 09:51 PM
I like the idea of a pneumatic powered setup because of the loud noise and vibration. I would think you could control this setup almost like you would if you were setting up a IR sensor break. So if you break the sensor it turns on the device and then off again maybe even throw in a BooBox or something for better control. One thing I would say is to weld a U shaped channel to the bottom of the panel so your vibrating device would hit that and never the panel your guests would walk on directly. If it ever wore through the channel then its just adding some more metal to the channel for a fix and would never be able to hit your guests. Just my thoughts on this idea but I think it would be a great startle scare. If you get it figured out I'd like to hear what you ended up with.

gadget-evilusions
07-07-2013, 08:02 PM
here is an older thread on the same thing- read Gadget's comments
http://www.hauntworld.com/haunted_house_forums/showthread.php?910-vibrating-floor

I like when something I said years ago pops back up!

Mad Wax Sculptor
07-10-2013, 12:24 AM
slap a $60 saws all to the bottom of the plate minus the blade and zip tip the trigger . its cheap , safe and effective

rfsystems
07-14-2013, 04:50 PM
Keep you eyes out for old paint shakers... if you see one, buy it! They work great.