HauntWorld Home - Forums Home - Live Chat - Find Haunted Houses - Hauntworld Magazine - Haunted House Supplies - America's Best Haunts - Find Vendors
Haunted House News - Haunted Tradeshows - Join Hauntworld Facebook - Hauntworld Twitter - Advertise - Contact Us

Thread: airbrush problems

Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. Default airbrush problems 
    #1
    Join Date
    Apr 2012
    Posts
    76
    I am having huge airbrush problems. I bought a airbrush and it only worked for one day[it was used]. I thought it might have been clogged but I cleaned it real good and air blows freely but I still can not get the make up to come threw[I made sure the part on the gun that feeds the paint in was not clogged either]. Also all I could get the gun to do was make thick lines when I need thin lines for my face paint. I heard if I take the front off all the way to the needle it gives out thin lines but could not try it do to the gun not working. What do you guys think the problem is with the gun[the compressor is blowing out consistent and there is no problems with the line I am STUMPED]. Also its not the paint you have to dilute so I do not know. Also how do you make thin lines with the gun. THANX
     

  2. Default  
    #2
    Join Date
    Mar 2010
    Location
    Connecticut
    Posts
    1,209
    You only have one head for the brush?

    Different heads are meant to be screwed onto the tip of the brush, some make thin lines some make thick lines, but to me it still sounds like it's a makeup issue. If the air is fine, and you can see and feel that the air is being blown properly, you either have a clog in your feeder (is it a bottom or top feed gun?) or it's your makeup....is your compressor attached to the airbrush? as in, are you using a small compressor that came with the airbrush, or are you using a real compressor?? maybe you feel the air coming out but the psi may be too low... we really need more information to help you out.
     

  3. Default operational procedures 
    #3
    Join Date
    Aug 2003
    Location
    Abcynthiana
    Posts
    1,187
    Basic operational procedures regardless of airbrush

    But it would help to know what model, type etc of airbrush. Not all airbrushes are created equal.

    paint should be the consistency of milk
    pressure at 30 to 35 psi, lower if you are trying to get very thin lines.

    Where most clogs happen is in the tip right where the needle peaks through. You have to remove the tip and take an old needle and scrape inside the tip and pull out the clog.
    YOu also want to always strain the paint so you don't get improper mixed paint and chunks in the bottle or feed.

    Have you read any instructions on how to use the airbrush.
    It helps to know what the parts terms are. body, tip, cap
    Also, if you airbrush starts spitting, then you are getting clogged or you have water in your lines. It would help to have a water trap at the base of your airbrush air line.

    etc...
     

  4. Default Info 
    #4
    Join Date
    Apr 2012
    Posts
    76
    Of course the gun is hooked up to the air compressor how else would air be blowing threw. The gun and compressor is paasche and the compressor is 1/10 horse power. It is a bottom feeder gun and it just seems like it does not want to suck the paint up. The paint is the same thickness as milk. Maybe there is just not enough psi and I need to go by something new.
     

  5. Default  
    #5
    Join Date
    Nov 2008
    Location
    Mesquite, TX
    Posts
    2,788
    1/10 HP is a really weak compressor. I recommend 1/5HP or stronger, we ask a lot of them and the smaller ones will overheat and blow.
    Try running water through your airbrush, If it shoots water then it should shoot well mixed paint. Is the paint clumpy?was it allowed to get real cold or real hot? is it old?
    I normally paint at 40psi, so try upping the pressure a bit.
    Allen H
     

  6. Default  
    #6
    Join Date
    Aug 2003
    Location
    Abcynthiana
    Posts
    1,187
    Paasche is a good brand of air brush. You cant go wrong unless the airbrush is not complete.
    But Allan is right. If you put water in a bottle and it shoots that then you know your paint is either too thick or your air pressure is too low.
    Also check the vent on the bottle. If it is clogged it won't pull anything.
    Or if the paint is shooting up out of the vent then you have a complete clog that is blocking air and paint.
     

  7. Default Damn thats frustrating 
    #7
    Join Date
    Mar 2011
    Location
    Raleigh, NC
    Posts
    388
    I had this problem myself a few seasons ago and it really is frustrating, but what I found is exactly what Allen and everyone else is saying. The tip was clogged. Even after cleaning! I ended up using a trick that my wifes nail artist showed us - she cleans her guns with Windex. Just make sure you run water through it before painting someones face. I usually keep a little bowl of Windex at my station, and drop the gun in there when I am done or need to clean. Than I run water through it and change colors. Last year I used Passche (gun and compressor) and had no problems whatsoever. Hope you find it!
    Travis "Big T" Russell
    President
    Big T Productions Inc

    Owner and Operator of "The Plague" and "Camp Nightmare"

    Customer Quote of the year: "Damn, I pissed myself"
     

  8. Default Clogged again! 
    #8
    Join Date
    Mar 2011
    Location
    Raleigh, NC
    Posts
    388
    Just to add based on this years experience. Last year I used all Mehron makeup in the airbrush and had no problems. This year I used Graftobian and found problems with some colors. Dark pigments were the worse (black and red for example). I found a few problems. First, I was using bottles, and the paint was clogging in the tube inside the bottle. Lighter colors were no problem, and I ended up diluting the dark pigments quite a bit to get them to work. I also had to shake them really good before every application because the Graftobian paint tends to settle to the bottom really quick.

    I also had problems keeping the tip clear with these paints. I spent a lot of time removing the tip, removing the needle, and cleaning thoroughly the entire gun. I remedied this by having one bottle full of Windex and one of water. When changing colors, I would first spray the Windex through the gun to clean everything real good. Then I would use the water to make sure everything was rinsed out well and it was still spraying evenly.

    This solved all the problems and I was back up and running although still challenged with the darker pigments. I think I will go back to Mehron next year as I had fewer problems with their paint.
    Travis "Big T" Russell
    President
    Big T Productions Inc

    Owner and Operator of "The Plague" and "Camp Nightmare"

    Customer Quote of the year: "Damn, I pissed myself"
     

  9. Default  
    #9
    Join Date
    Aug 2003
    Location
    Tyler, Texas, United States
    Posts
    2,614
    Paasche also has this little condition where to suck paint or fluid from a bottle the back of the tip has to seal properly. Many times they do not right from the factory and so I put a rubber o-ring over it and then screw the tip on. For serious cleaning you can take it all apart and use carburetor cleaner, which is an aerosol can of acetone so good for outdoors. There are a couple little ports that are the air feed and if you don't have them all or it isn't sealed to go out the end, it is not going to flow.

    Just get used to taking apart every piece of a tip, needled, body etc. That is just the way it is. I have gotten lots of air brushes where someone used them once and then it didn't work. After cleaning everything with the acetone and air, only a few places would need re lubed at the trigger area. I use marvel mystery oil or vaseline works.

    To get thin lines you get the air brush really close to the surface and there are 3 different tips that go to a Paashe. Each have their own needle. But, now I'm not sure if you have a single action or a double action. If it is a single action, you indeed change the tip screwed in or out just like an old fashioned garden hose. If it is double action, YOu can sometime not have enough pressure happening. It takes at least 35 psi to pull paint up. If it is very thick you might have to go to 60 psi. If you have to go to the higher PSI it is not great material to be doing make up near someone's face.

    The other fun thing is paint and makeup sits on shelves for a couple years and in a warehouse for 4 years before than and is "brand new" So you get familiar with what everything thins with and screen out the material like Kevin says.
    Last edited by Greg Chrise; 11-05-2012 at 04:16 PM.


    Another fabulous post from the U.S.Department of Wild Imaginings, now in spectaclar stereo, sponsored by the Adhesives and Sealants Council, suggesting ways to stick things together since the 1800s. Not fabulous in a gay way. Your results may vary. Illinois residents add 8% sales tax. These posts have been made by professional post makers, do not try this type of posting on your own without extensive training, lovely assistants and a trusty clown horn.
     

  10. Default  
    #10
    Join Date
    Aug 2003
    Location
    Tyler, Texas, United States
    Posts
    2,614
    Once you figure out what is limited with the Paasche, and understand what all the pieces do, then buy Iwata anythings. Eclipse or HP-C models. Then even the most super accessorized paasche just sits around as a back up for about 15 years at a time.


    Another fabulous post from the U.S.Department of Wild Imaginings, now in spectaclar stereo, sponsored by the Adhesives and Sealants Council, suggesting ways to stick things together since the 1800s. Not fabulous in a gay way. Your results may vary. Illinois residents add 8% sales tax. These posts have been made by professional post makers, do not try this type of posting on your own without extensive training, lovely assistants and a trusty clown horn.
     

Thread Information
Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •